Freezes on the logo
The unit gets stuck on the logo and does not boot up. We determine the cause after checking the module and carry out software repair or any other necessary work.
Do you have a problem with freezing on the logo, resets or code lock? We repair Zenec Z-E2015 units fitted to Seat, Škoda and Volkswagen vehicles. Send the removed module with a description of the symptoms, and we will check it and confirm the repair scope.

Written repair warranty
Quote for approval before repair
Courier shipping from anywhere in Poland
Quick repair quote
Zenec Z-E2015 is a radio from Zenec, a replacement for the factory unit dedicated to Seat models (including Altea, Leon, Alhambra), Škoda models (including Octavia II, Rapid, Superb II) and Volkswagen models (including Golf, Passat B6–B7) from around 2003–2015, depending on the model.
The unit supports steering wheel controls and connects to the car’s computer via the CAN bus and to on-board displays. The radio has a user-selected security code — a 4-digit code active until the unit is disconnected from the battery.
When submitting a case, provide a description of the symptoms and you may send a photo of the label with the part number. Send only the removed module by courier; we check the module at the workshop and confirm the scope of work.
The symptoms help describe the fault. We confirm the cause after checking the removed module.
The unit gets stuck on the logo and does not boot up. We determine the cause after checking the module and carry out software repair or any other necessary work.
The radio restarts or resets without your input. After checking the module, we will confirm whether software repair or component replacement is required.
The unit uses a 4-digit security code, and entering random codes may lead to a permanent lockout. Once we receive the module, we will check whether access can be restored and what work is needed.
The touchscreen may work incorrectly or stop responding altogether. We confirm the extent of the fault after checking the module and select the required work.
We inspect the removed module in our workshop, describe the faults and confirm the scope of work and the price before the repair starts.
We can carry out software repair and make the necessary changes if, after checking the module, we confirm that this is the required work.
If a part needs replacing, we do it after confirming the scope; once repaired, we test the module and send it back safely packaged.
We repair your own unit; we do not replace it with a used one from the market. You decide whether to proceed with the repair after the module check and approval of the scope of work and price.
You do not need to bring the vehicle in. Describe the problem and we will help you work out what to remove and send. After inspection, you will receive a quote for approval — only then will we start work.
01
Write what is happening in the vehicle, state the make, model and year. Add a photo of the device, the error screen or the nameplate sticker, if you have one. On that basis, we will initially assess whether we can help.
02
Not sure whether to remove the radio, screen, amplifier or another unit? We will advise which component to check, how to prepare it for shipping and how to pack the parcel safely.
03
In the workshop we carry out diagnostics, confirm the source of the problem and define the scope of work. We send a quote for approval. We only start work after your approval.
04
We remove the cause of the fault, test the device and send it back safely packed for refitting. Every repair we carry out is covered by a warranty.
Answers to questions about the Zenec Z-E2015 and the sending process.
Freezing on the logo is one of the faults we repair in Zenec units. We will confirm the scope of work and cost after checking the module.
We can reset a unit locked after random code entries at the workshop. We confirm the scope of work after checking the module.
If you decide not to proceed, the unit cannot be repaired, or the fault lies elsewhere, diagnostics and return shipping are free of charge. We start the repair after your approval of the scope and price.
If a component needs replacing, we will carry it out after confirming the scope of work. We can source the required parts, and we will confirm the cost and scope after checking the module.
The unit's security code is chosen by the user.. have you forgotten which one you set?